HRC Racing
HRC15012BL-1
Car - 1/10 XL Electric - 4WD Pickup Truck - RTR - HRC NEOXX - Brushless - Scrapper V2 RED/BLACK
The NEOXX V2 Scrapper from HRC RACING is an all-wheel drive 4WD monster truck in 1:10 XL scale.
The NEOXX V2 models from HRC RACING have two large bumpers at the front and rear. With LED lights installed in the front and rear bumpers, night becomes day! The bodywork is made of robust Lexan polycarbonate.
The model is splash-proof for driving fun in all weather conditions!
The internal components are supported by a robust base plate made of high-quality aluminium.
3 adjustable oil differentials ensure optimum power distribution between the front and rear axles and improved traction. With the differential function, the driving behaviour can be adjusted to be milder or more aggressive as required.
Encapsulated transmission components reduce stone chipping and the risk of injury.
At the front axle, the bone has been connected to the wheel axle to form a universal CVD drive shaft. This allows more steering angle and ensures less friction loss. In addition, the bone is no longer lost in the event of hard impacts.
Adjustable oil pressure shock absorbers ensure good damping when jumping and cornering.
A wall on the side of the chassis plate allows less dirt to enter the vehicle.
The model is equipped with energy-saving ball bearings. High-quality tyres with high traction give the model very good grip on any surface.
To ensure a long service life and high performance, the HRC NEOXX V2 models are fitted with electronic components from well-known brands. A high voltage level and a high capacity of the supplied batteries ensure maximum acceleration and top speed in addition to a longer driving time.
The complete RTR set is supplied with the 2.4 GhZ NEOXX FS-G4P transmitter from HRC RACING. The transmitter has all the important trim controls and 4 channels. Optionally, LEDs or winches, for example, can be controlled via the free channel 4.
With the 220V quick charger, batteries can be recharged within a short time.
The controller, batteries and charger are equipped with new custom-fit XT60 high-performance plugs.
With the combination of NEOXX FS-G4P transmitter and HRC RACING ZTW BEAST G2 brushless speed controller, the pilot has the option of reducing the speed by 50% at the touch of a button. This function gives the driver the option of adjusting the speed to suit their driving ability.
The HRC ZTW BEAST G2 controller can also be programmed with the optional programming card ZTW1300011 or via the Mobile APP & ESC module ZTW2200011. This enables fine adjustment of the controller, such as setting the braking force.
Spare parts are easily available from any good r/c modelling dealer if required. NEOXX and HRC RACING wish you lots of fun with the hobby!
Specifications NEOXX SCRAPPER TRUCK (Brushless):
- 1/10 XL wheelbase 300mm
- Overall length 460mm
- Large XL front and rear bumpers
- Bodywork made from robust Lexan polycarbonate
- LED lights front and rear
- Throttleable motor power via transmitter
- Splash-proof onboard electronics
- 3 differentials (front, centre, rear) for improved traction
- Aluminium base plate
- Adjustable oil pressure shock absorbers
- Motor heat sink for improved heat dissipation
- Aluminium shock tower (brushless)
- Low friction ball bearings
- 2.4GhZ NEOXX transmitter from HRC RACING
- 2.4GhZ NEOXX receiver from HRC RACING
- APP programmable ZTW 60A speed controller (XT60 connector)
- HRC RACING 3660 motor 3300 KV
- Splash-proof on-board electronics
- HRC RACING 11.1V 3600 LiPo battery
- HRC RACING Balance quick charger
- Maximum speed: 35-75 KM/H
- High-quality universal front drive shaft
Required accessories:
4 AA batteries for transmitter
Optional:
Programming card for controller ZTW1300011
APP module for controller ZTW2200011
Recommended price: 329.95 EUR
| HRC28321-3 | Setup Tools |
| Spare parts - Buggy setup station - Gasket (1 pc) | |
| HRC28321-2 | Setup Tools |
| Spare parts - Buggy setup station - Connecting nut with screws (1 pc) | |
| HRC28321-1 | Setup Tools |
| Spare parts - Buggy setup station - wheel nuts (1 pc) | |
| HRC28325-2 | Setup Tools |
| Spare parts - Touring setup station - Connecting nut with screws (1 pc) | |
| HRC28325-1 | Setup Tools |
| Spare parts - Touring setup station - wheel nuts (1 pc) | |
| HRC08208X6 | Batteries |
| Battery - Li-Ion 2s - 7.4V 800mAh 15C - No Case - XT60 - 55 x 34 x 17mm | |
| HRC04457D | Batteries |
| Battery - LiPo 4S - 14.8V 5700mAh 100C - Hard Case Slim LCG- Ultra T - 138x47x37mm | |
| HRC01650T | Batteries |
| Battery - 6 cells - NiMH - 7.2V 5000mAh - Stick - TRX - 130x45x25mm | |
| HRC15-P997 | Bodies 1/10 |
| Spare Part - Neoxx V2 - Chasis side guard & body roof protector | |
| HRC15-P996 | Bodies 1/10 |
| Spare Part - Neoxx - Tail wing bracket connector - Artemix | |
| HRC68144HVBL-A9 | Servos |
| Servo Gear Set - for HRC68144HVBL - 9T 2021-2023 | |
| HRC28325 | Setup Tools |
| Tool - 1/10 - Setup Station Touring - with bag | |
| HRC28321 | Setup Tools |
| Tool - 1/10 - Setup Station Buggy - with bag | |
| HRC5902 | Setup Tools |
| Car Stand - Grip Pad self adhesive - 180x 93mm | |
The photos, descriptions, dimensions and prices of the products are for illustrative purposes only. They are subject to change at any time. We cannot accept any liability for technical or typographical errors.
HRC Racing ...
... top products for every RC fan !
Copyrights © code & design: AdaptaWeb |
Copyrights © contents: HRC Distribution
Last update 21.11.2024